Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Don't take too lightly the forklift at the workplace. If the operation is not good, there will be severe crashes in mins, and there are several accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Start.
1. Prior to starting, observe the surroundings, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a tons, the vehicle driver must initially verify that the lots is steady and dependable.
4. The beginning must be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must comply with the traffic rules in the factory and must keep a specific security distance from the car ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or filling. .
8. The elevation of the tons need to not block the motorist's sight. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be fixed and reported in a prompt manner, and they will never ever operate with illnesses or hide them.

packing and discharging.
1. When fork-loading items, the range between both forks must be changed as required to make the tons of the two forks well balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or draw. In unique circumstances, safety and security warning signs have to be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift must be stopped with the brake. .
4. The rate of the automobile should be sluggish and Stand-on Electric Pallet Stacker steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork idea should not touch other items or objects. The tons should be supported with marginal back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to Electric Forklift Truck for Warehouse loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be added.
2. Examine the safety performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you run into a person in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the tendency of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and progress, if they come across large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844